Products Description
Acetoxy Silicone Sealant is a one-part, silicone sealant;
A non-toxic, solvent-free silicone sealant for use in aquarium construction and glazing applications. It's a high-quality acetic curing system based silicone sealant featuring excellent adhesion to glass and many other non-porous surfaces.
Features & Benefits
1.100% solventless silicone;
2.Non-toxic to fish;
3.Resistant to water, UV and many chemicals;
4.One component, cures with atmospheric moisture;
5.Keeps its elasticity at low and high tempratures;
6.Rapid curing;
7.Very good bond and physical strenght.
Applications
1.Construction and repair of aquariums and many glass structures;
2.Suitable on glass/alumi-num structures;
3.Glazing on aluminum frames and shop displays;
4.Sealing of windows and doors.
| Consumption (approx.) |
| Joint Width | 6mm | 9mm | 12mm |
| Joint Depth | 6mm | 6mm | 6mm |
| Efficiency/300ml | 8meters | 6meters | 4meters |
| Consumption (approx.) |
| Following cleaning procedure and materials are recommended: |
| Glass | Degrease with alcohol or MEK |
| Aluminium, light alloys and stainless steel | Degrease with alcohol or MEK |
| Other Metals | Lightly abrade then degrease as above |
| Wood | Lightly abrade surface then remove dust |
| Plastics | Degrease using an agent recommended by plastics manufacturer |
Instructions
1.Ensure that surfaces to be sealed are clean, dry and grease free;
2.The application temperature must be between +5℃ and +40℃;
3.After the application, the sealant must be tooled with light pressure within 5 minutes to spread the material against the joint surfaces and to obtain a professional finish;
4.Excess uncured sealant may be cleaned with solvent. Cured sealant can be removed barely mechanically;
5.6mm.joint depth is recommended for joint widths between 6 mm to 12mm;
6.After the construction of aquarium is complete, wait for minimum of 21 days before usage.
Standards
Meets or exceeds the requirements of the following speci-fications:
1.ISO 11600 F & G 20LM;
2.CE marked for EN 15651 for façade, glazing and sanitary;
3.The requirements of VOC content specifications in LEED credit EQc4.1 "Low-emitting products" of SCAQMD rule 1168.
Safety & Disposal
Inhalation of the sealant vapor for a long period must be avoided. The application area must be ventilated properly.The uncured sealant must not be contacted for a long period. Cured silicone rubber bears no risk to health.temperatures between +5℃ and +25℃. Check MSDS guide-lines for disposal and further information concerning safety.
Restrictions
1.It must not be used in totally confined spaces where sealant cannot cure due to lack of atmospheric moisture;
2.Not over paintable;
3.Do not expose to water before fully cured;
4.Do not use in conjunction with bitumen asphalt,neoprene and certain organic elastomers;
5.Do not use to produce swimming pool joints;
6.Can yellow if exposed to bleach or HCL based brick clean-ers whilst curing.
| TDS |
| Basis | Silicone Polymer |
|
| Curing System | Acetoxy |
|
| Density | 1.02±0.03g/ml |
|
| HardnessShore A | 24-30(after 28 days) |
|
| Tensile Strength | ≤0,4N/mm2 | (ISO 8339) |
| Skin formation | 5 minutes (23℃and 50% R.H) |
|
| Curing Rate | Min.3mm/day (23℃and 50% R.H) |
|
| Elongation At Break | ≥250% | (ASTM D412) |
| Elastic Recovery | %100 | (ISO7389) |
| Sagging | 0mm | (ISO 7390) |
| Change in volume | < 5% | (ISO 10563) |
| Temperature Resistance | -50℃ to +200℃ |
|
| Application Temperature | +5℃ to +40℃ |
|
Storage & Shelf Life
The shelf life is 18 months if stored in unopened-original package in a dry place at temperatures between +5℃ and +25℃.
Tel: +86-15966176633
